First verify the actual configuration of T45
The used Epiroc FlexiROC T45 is a top-hammer drill rig. Check the installed boom, rod threads and rod-handling system against your bench height, target hole depth and existing tooling to assess whether the configuration suits the job.
Compare the seller’s description with the machine’s serial number, configuration documents and inspection records before discussing the price.
First check the rock drill, boom and threads
The rock drill is the heart of a top-hammer rig. Its model, serial number and manufacturer information help identify a matching shank adapter and tools, but physical verification is still required. Epiroc's T45 series brochure shows recommended boom and thread combinations: T51/T60 in the standard-boom table and T45/T51 in the folding-boom table. Machines with the same name may therefore have different threads, fundamentally changing your tooling configuration.
First request a clear photo of the rock-drill nameplate, confirm the boom type, which can be identified by its geometry, and check the thread specifications of the tooling actually fitted. Also ask about feed length and maximum rod length. These details help assess whether the rig can meet your requirement to drill the full bench in one pass.
Repeatedly demonstrating the drill rod handling cycle
The appearance of the rod-handling system alone cannot establish the machine's actual age or condition. A carousel that looks normal without load may have worn jaws or alignment errors that could cause a fault during the cycle. To assess attainable hole depth, consider carousel capacity, rod lengths and the machine's actual configuration; the condition of the supports and feed rails is equally important.
Request video of the machine repeatedly loading and unloading a full set of rods. If an on-site demonstration is needed, have a qualified operator demonstrate the cycle according to the applicable equipment manual when equipment and site safety conditions permit.
Dust and Air: What Site Tests Conceal
An underperforming or blocked dust collector may affect dust control, and a short no-load test may not expose the problem. Check the compressor air supply, dust collector and filter elements, and observe system performance under actual site load.
Request a cold-start video and, if possible, a short video of drilling under load. Look for smoke, unusual rock-drill noises and the dust-control performance of the dust collection system. Also ask for compressor operating hours and hose condition. The dust system's condition is one clue to maintenance, but must be considered with other records and inspections.
Materials to request before discussing price
Before seriously discussing the price of a used Epiroc FlexiROC T45, get the configuration sheet first. It should list the rock drill model, boom type, rod thread and length, starter rod, rod magazine capacity, feed beam length, dust collector model, air compressor type and engine hours.
Also confirm which tools and consumables come with the machine, such as drill rods, bits and compatible couplings. A machine without usable tools may add to procurement costs. Request an exact list of the items actually included and their condition.
Test-day steps that reveal the true condition
If the configuration is suitable, arrange an on-site inspection. When equipment and site safety conditions permit, have a qualified operator follow the applicable equipment manual to perform a cold start and listen for unusual hydraulic noise, then drill a test hole with compatible tools and observe the rock drill under load.
Check for oil leaks around the shank adapter and scratches on the feed rails, and listen for clicking. Have a qualified operator demonstrate the carousel loading and unloading cycle according to the applicable equipment manual when equipment and site safety conditions permit. Observe clamping, release and dust control from a safe position. Check the filters and associated hoses according to the manual, record faults, and have qualified personnel assess them and complete necessary repairs before production.
Check missing configuration details
Ask the seller for missing configuration documents and photos, along with a list of tools included with the rig. Confirm thread specifications and tooling compatibility before assessing the price of the rig and its included tools; list separately any tools not yet confirmed or not included.
You can also compare the FlexiROC T45 with the T35 or T40 when evaluating your options.
Your inquiry: what to send to GLOBMACH
When you are ready, send a structured inquiry for FlexiROC T45. Please specify your target hole diameter and depth, rock type and bench height, current thread system, production target and destination. This helps the seller match a suitable machine for you and pull up the specific configuration you need.
Mention local support for parts and tools. If components cannot be obtained quickly, even a T45 that suits your quarry may not be practical. You could say: "I'm looking for a used Epiroc FlexiROC T45. Can you confirm the thread system, boom type, rock drill condition and included tools? I also need to know whether the rod magazine can complete a full cycle." This will get you a useful reply faster.
